Dental And Ceramic And Shade

OBJECTIVE: To explore and characterize the effect of the discrepancy between crestal bone height (CB) and pulp chamber floor (PCF) in the fatigue performance of endodontically-treated teeth rehabilitated with an endocrown restoration. MATERIALS AND METHODS: A total of 75 human molars free of defects, caries history or cracks were selected, then endodontically treated and randomly allocated into 5 groups (N = 15) according to the difference between PCF and CB, as follows: PCF 2 mm above, PCF 1 mm above, PCF leveled, PCF 1 mm below and PCF 2 mm below...

OBJECTIVES:  Firing protocols influence optical properties of dental ceramics. Effects of varying cooling rates of monochrome and multilayer 5 mol% yttria-stabilized tetragonal polycrystalline (5YTZP) on optical properties are subjected for investigation. MATERIALS AND METHODS:  Ninety specimens (width, length, thickness = 10 × 20 × 2 mm) were prepared from monochrome (Mo: Cercon xt) and multilayer (Mu: Cercon xt ML with cervical (C) and incisal (I) zoning) 5YTZP...

PURPOSE: To evaluate color differences in repair of indirect ceramic and resin nanoceramic CAD/CAM blocks with two universal shade composites after different surface preparations. MATERIALS AND METHODS: 120 samples were prepared from IPS Empress and GC Cerasmart270 CAD/ CAM blocks and thermocycled (5000 cycles, 5°C-55°C). Initial colors of sample surfaces were measured using a spectrophotometer. Rectangular prism-shaped cavities were prepared and repaired with Tokuyama Universal Bond/Omnichroma and G-Multiprimer/G-Premio/Essentia Universal following surface preparation with aluminum oxide, Cojet, and bioactive glass (Sylc)...

PURPOSE: This in vitro study evaluated the color differences when discolored tooth substrates were restored with CAD-CAM monolithic ceramics depending on ceramic type and thickness, and the try-in paste shade. METHODS: Six ceramic types were tested: high-translucent lithium disilicate (LD-HT); medium-translucent lithium disilicate (LD-MT); low-translucent lithium disilicate (LD-LT); low-translucent leucite (LC-LT); feldspathic ceramic (FC); BL1 low-translucent lithium disilicate, stained to A1 shade (LD-BL1-LT)...

OBJECTIVES: To evaluate the effects of background color, ceramic type and coping thickness on masking ability (ΔE) and translucency parameter (TP) of CAD/CAM lithium disilicate glass-ceramic/monolithic zirconia and, to determine the correlations between coping thickness, TP and ΔE. METHODS: A total of 120 ceramic specimens (2 mm, 1 mm and 0.5 mm thickness; n = 10) of four CAD/CAM ceramics: IPS e.max, IPS ZirCAD, Upcera Li CAD and Upcera TT CAD, were studied...

The cementation of indirect restoration is one of the most important steps in prosthetic and restorative dentistry. Cementation aims to bond the prosthetic restoration to the prepared enamel or enamel and dentine. Successful cementation protocols prevent biofilm formation at the margin between tooth and restoration and minimize mechanical and biological complications. With the advancements in dental cements, they have been modified to be versatile in terms of handling, curing, and bond strengths. This review presents updates on dental cements, focusing on the composition, properties, advantages, limitations, and indications of the various cements available...

BACKGROUND: The aim of this study was to evaluate the color stability and the surface roughness of a bulk-fill composite flow (SDR® Plus) by comparison to an ORMOCER-based composite (Ceram.x® Universal SphereTEC™) in order to confirm the validity of using SDR® Plus in the anterior region and to allow the prediction of its long-term results. MATERIAL AND METHODS: 35 composite specimens of the same shade (A2), thickness (2mm) and shape of both types of composite were prepared...

BACKGROUND The majority of dental professionals currently recognize lithium disilicate E-max ceramic veneers as a the most widely used, conservative, and effective cosmetic materials in dentistry. This study aimed to compare the degree of surface changes - roughness (Ra), depth (Rz), and mean color changes (ΔE₀₀) - of computer-aided design-computer-aided manufactured (CAD/CAM) ceramic veneers materials of varying thicknesses caused by staining by green tea, coffee, and Coca-Cola using digital spectrophotometer...

Usually, dentin and enamel shades are layered in dental restorations with the purpose of mimicking the natural appearance of teeth. The main objective of this study was to develop and assess accuracy of a color-prediction method for both monolithic and layered dental resin-based composites with varying shades and under different illuminants. A total of 15 different shades of VITAPAN Excell, VITAPAN Dentine and VITA Physiodens as well as VITA Enamel of five different thicknesses (0.5-2.5 mm range) were used to manufacture monolithic and layered samples...

PURPOSE: The available independent data on the translucency of novel pre and fully sintered chair-side computer-aided design and computer-aided manufacturing (CAD-CAM) lithium disilicate are limited. This comparative in vitro study evaluated the translucency degree of pre and fully sintered chairside CAD-CAM lithium disilicate crowns after optional, required, and additional firing processes. MATERIALS AND METHODS: One hundred and five maxillary left central incisor crowns manufactured by three different CAD-CAM lithium disilicate brands shade A1 were assigned into 7 groups as follows (n = 15): (1) n!ce Straumann without sintering; (2) n!ce Straumann with one additional sintering process; (3) n!ce Straumann with two additional sintering processes; (4) Amber Mill with one sintering process; (5) Amber Mill with two sintering processes; (6) IPS e...

OBJECTIVES: The aim of this study was to evaluate the accuracy of machine learning regression models in predicting the final color of leucite-reinforced glass CAD/CAM ceramic veneer restorations based on substrate shade, ceramic shade, thickness and translucency. METHODS: Leucite-reinforced glass ceramics in four different shades were sectioned in thicknesses of 0.3, 0.5, 0.7, and 1.2 mm. The CIELab coordinates of each specimen were obtained over four different backgrounds (black, white, A1, and A3) interposed with an experimental translucent resin cement using a calibrated spectrophotometer...

OBJECTIVES: To evaluate and compare fracture resistance, translucency, and color reproducibility, as well as the effect of aging on the fracture load and color stability of novel monolithic CAD/CAM ceramics. MATERIALS AND METHODS: One hundred crowns of uniform thickness were milled from five ceramic blocks (n = 20): partially crystallized lithium disilicate (PLD) and fully crystallized lithium disilicate (FLD), lithium metasilicate (LMS), 4Y-TZP (SMZ), and 5Y-TZP (UMZ) monolithic zirconia...

The effect of a novel nano-ceramic coating (TiO2 ) using an atomic layer deposition (ALD) technique on the surface of polymethyl methacrylate (PMMA) material was investigated. The patients' and clinicians' perception and acceptance of the PMMA color with TiO2 coating were also examined. In vitro color measurement was performed on thirty specimens (light, original, and dark pink) before and after TiO2 coating. Patients' and clinicians' perception and acceptance of color changes on PMMA were measured and compared...

OBJECTIVES: To evaluate the effect of thickness on color and translucency of a multi-color polymer-infiltrated ceramic-network (PICN) material. METHODS: Specimens of 0.5, 1.0, 1.5 mm thicknesses were obtained by sectioning VITA ENAMIC® multiColor (E-MC) High Translucent CAD-CAM blocks (1M1-HT, 1M2-HT, 2M2-HT, 3M2-HT, and 4M2-HT). Spectral reflectance and color coordinates were measured on white and black backgrounds using a spectroradiometer, CIE D65 illuminant and CIE 45°/0° geometry...

By utilising open-source digital software, clinicians can create an integrative digital workflow composed of various technological systems. This report presents a clinical case that follows a comprehensive digital workflow to improve the smile of a 42-year-old female patient. The patient presented with minor attrition of maxillary anterior teeth and discoloured, asymmetrical composite restorations on central maxillary incisors. Her smile was rehabilitated by restoring her maxillary anterior teeth with lithium disilicate ceramic veneers...

Crown restorations in anterior region are recommended highly color-reproductivity because of aesthetic reason. Composite resin block with several shade gradations is especially produced for anterior restorations. To clarify the durability of an aesthetic, the effect of toothbrush abrasion on surface properties was performed. Composite-resin blocks without shade gradation and a ceramic block were used as controls. All specimens were prepared using #2000 SiC paper and polished using an aluminum oxide polishing paste...

OBJECTIVE: To characterize the effect of pigmentation techniques on the fatigue behavior of a 4YSZ ceramic adhesively luted onto dentin analog (glass fiber-reinforced epoxy resin). METHODS: 4YSZ ceramic discs (Ø= 10 mm, 1 mm thickness) were allocated into 5 groups: Ctrl - unshaded (IPS e.max ZirCAD MT BL); Manuf - shaded by the manufacturer (IPS e.max ZirCAD MT A2); Brush - unshaded pigmented, pre-sintering, using a brush; Stain - unshaded pigmented, post-sintering, during glaze application; Brush+Stain - combination of both techniques...

This study evaluated the color and microstructure of monolithic zirconia crowns with different yttrium oxide (Y2 O3 ) contents treated by conventional or speed sintering. Four types of zirconia ceramics were assessed: two monolayer zirconia, and two multilayer zirconia. The monolithic zirconia crowns were fabricated using a dental computer-aided design/computer-aided manufacturing (CAD/CAM) system and in two shades (A2 and BL). After milling, the zirconia crowns were sintered using either speed sintering or conventional sintering...

This study aimed to investigate and compare the color stability and stainability of computer-aided design/computer-aided manufacturing (CAD/CAM) restorative materials in their glazed (G) and polished (P) state when exposed to cigarette smoke, as well as after brushing. Three CAD/CAM restorative materials were investigated: lithium disilicate CAD (LD), zirconia (Zr), and Telio PMMA CAD (PMMA), according to their surface finishing and assignment to cigarette smoking exposure or soaking in the saliva (control) group...

The aim of this study was to investigate the effect of repressing leftover heat-pressed lithium disilicate material on its mechanical and optical properties. A lithium disilicate ingot (IPS e.max® Press, IvoclarVivadent, Schaan, Liechtenstein) shade (A1) low translucency was first heat-pressed to yield ceramic bars and disks. Then, the second and third presses were fabricated from the leftovers of the previous pressing cycles. A total of 36 bars and 15 disk specimens were fabricated and divided into three groups according to the number of pressing cycles (n = 12 bars and n = 5 disks): P1: first press (control), P2: second press, and P3: third press...