Filler

This study designed a two-stage, electrode-integrated septic tank-floating wetland system and assessed their pollutant removal performances under variable operational conditions. The two-stage system achieved mean organic, nitrogen, phosphorus, and coliform removal percentages of 99, 78, 99, and 97%, respectively, throughout the experimental run. The mean metals (chromium, cadmium, nickel, copper, zinc, lead, iron, and manganese) removal percentages ranged between 81 and 98%. Accumulated sludge, filler media, and the hanging root mass contributed to pollutant removals by supporting physicochemical and biological pathways...

High-power-density electronic devices under vibrations call for soft and damping thermal interface materials (TIMs) for efficient heat dissipation. However, integrating low hardness, high damping, and superior heat transfer capability into one TIM is highly challenging. Herein, soft, damping, and thermally conductive TIMs are designed and prepared by constructing a honeycomb-board-mimetic boron nitride nanosheet (BNNS) network in a dynamic polyimine via one-step horizontal centrifugal casting. The unique filler network makes the TIMs perform a high through-plane thermal conductivity (> 7...

Constructed wetland systems have been widely used in China due to their advantages of good treatment effect, low cost and environmental friendliness. However, traditional constructed wetlands have challenges in application such as deactivation due to filler clogging, difficulty in filler replacement and low adaptability. To address the above problems, this research proposes a modular filler design constructed wetland based on the concept of assembly construction, which can quickly replace the clogged filler without destroying the overall structure of the wetland...

Injectable hyaluronic acid (HA) hydrogels have been popularized in facial aesthetics as they provide a long-lasting effect, low risk of complications, allergenicity tests are not required before application and can be easily removed by the action of hyaluronidases. On the other hand, the development of these systems requires in-depth studies of chemical mechanisms involved in hydrogel formation. Ideal dermal fillers should temporarily fluidize during extrusion through the needle and quickly recover their original shape after application...

N-methyl-morpholine-N-oxide (NMMO) was initially created as a plasticizer for starch to produce thermoplastic wheat starch. Subsequently, talc powder was used as a reinforcing filler to enhance the mechanical strength of thermoplastic biomass-based composite plastics. The chemical structure, crystal structure, and microscopic morphology were analyzed using Fourier transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy. Additionally, the thermal properties were explored through thermogravimetric analysis, differential scanning calorimetry, and dynamic mechanical analysis...

Materials from green resources boast a low carbon footprint, forming the foundation of the circular economy approach in materials science. Thus, in this study, waste poly(ethylene terephthalate) (PET) was subjected to depolymerization using propylene glycol (PG), and subsequent polycondensation with bio-based maleic anhydride (MA) produced unsaturated polyester resin (b-UPR). Bio-derived acryloyl-modified Kraft lignin (Kf L-A) served as a vinyl reactive filler in the b-UPR matrix to create b-UPR/Kf L-A composites...

Sulfur-driven autotrophic denitrification (SdAD) is a promising nitrogen removing process, but its applications were generally constrained by conventional electron donors (i.e., thiosulfate (Na2 S2 O3 )) with high valence and limited bioavailability. Herein, an immobilized electron donor by loading elemental sulfur on the surface of polyurethane foam (PFSF) was developed, and its feasibility for SdAD was investigated. The denitrification efficiency of PFSF was 97.3%, higher than that of Na2 S2 O3 (91.1%). Functional microorganisms (i...

The mathematical models available in DDSolver were applied to experimental dissolution data obtained by analysing carvedilol release from hypromellose (HPMC)-based matrix tablets. Different carvedilol release profiles were generated by varying a comprehensive selection of fillers and carvedilol release modifiers in the formulation. Model fitting was conducted for the entire relevant dissolution data, as determined by using a paired t -test, and independently for dissolution data up to approximately 60% of carvedilol released...

Incrementing thermal conductivity in polymer composites through the incorporation of inorganic thermally conductive fillers is typically constrained by the requirement of high filler content. This necessity often complicates processing and adversely affects mechanical properties. This study presents the fabrication of a polystyrene (PS)/boron nitride (BN) composite exhibiting elevated thermal conductivity with a modest 10 wt% BN content, achieved through optimized compression molding. Adjustments to molding parameters, including molding-cycle numbers, temperature, and pressure, were explored...

Digital light processing (DLP) techniques are widely employed in various engineering and design fields, particularly additive manufacturing. Acrylate resins utilized in DLP processes are well known for their versatility, which enables the production of defect-free 3D-printed products with excellent mechanical properties. This study aims to improve the mechanical and thermal properties of 3D-printed samples by incorporating mica as an inorganic filler at different concentrations (5%, 10%, and 15%) and optimizing the dispersion by adding a KH570 silane coupling agent...

This paper presents the obtaining and characterization of recycled polypropylene/strontium ferrite (PP/SrFe12 O19 ) polymer composite materials with applications in the electromagnetic shielding of vehicle interiors (mainly automotive electronics-carcasses) from the electromagnetic radiation emitted mainly by exterior sources-electrical lines and supply sources-in terms of the development of the new electrical vehicles. With this aim, suitable polymer composite materials were developed using SrFe12 O19 filler in two forms (powder and concentrate)...

The shuttle effect in lithium-sulfur batteries, which leads to rapid capacity decay, can be effectively suppressed by solid polymer electrolytes. However, the lithium-ion conductivity of polyethylene oxide-based solid electrolytes is relatively low, resulting in low reversible capacity and poor cycling stability of the batteries. In this study, we employed the activator generated through electron transfer atom transfer radical polymerization to graft modify the surface of silica nanoparticles with a bifunctional monomer, 2-acrylamide-2-methylpropanesulfonate, which possesses sulfonic acid groups with low dissociation energy for facilitating Li+ migration and transfer, as well as amide groups capable of forming hydrogen bonds with polyethylene oxide chains...

This paper presents the results of experimental investigation of the mechanical characteristics of 3D-printed acrylonitrile butadiene styrene (ABS) and its modifications reinforced with different types of short-fiber fillers: carbon, glass, and basalt. Elastic modulus, tensile and bending strength, as well as fracture toughness were determined in series of mechanical tests for samples produced with different manufacturing parameters, such as nozzle diameter and infill angle. It was found that the use of ABS filament reinforced with the short fibers can significantly improve the mechanical properties of 3D-printed devices when the infill angle is oriented along the vector of the applied load...

Over the past few years, polymer nanocomposites have garnered a significant amount of interest from both the scientific community and industry due to their remarkable versatility and wide range of potential uses in various fields, including automotive, electronics, medicine, textiles and environmental applications. In this regard, this study focuses on the influence of a compatibilizer rubber on a nanocomposite incorporating graphene nanoparticles (GNPs), with a polymer matrix based on a blend of polypropylene (PP) and polyethylene terephthalate (PET)...

This study investigated the synergistic effect of carbon black/multi-wall carbon nanotube (CB/MWCNT) hybrid fillers on the physical and mechanical properties of Ethylene propylene diene rubber (EPDM) composites after exposure to high-pressure hydrogen gas. The EPDM/CB/CNT hybrid composites were prepared by using the EPDM/MWCNT master batch (MB) with 10 phr CNTs to enhance the dispersion of CNTs in hybrid composites. The investigation included a detailed analysis of cure characteristics, crosslink density, Payne effect, mechanical properties, and hydrogen permeation properties...

Monitoring of molding processes is one of the most challenging future tasks in polymer processing. In this work, the in situ monitoring of the curing behavior of highly filled EMCs (silica filler content ranging from 73 to 83 wt%) and the effect of filler load on curing kinetics are investigated. Kinetic modelling using the Friedman approach was applied using real-time process data obtained from in situ DEA measurements, and these online kinetic models were compared with curing analysis data obtained from offline DSC measurements...

Fillers have been widely used in natural rubber (NR) products. They are introduced to serve as a strategy for modifying the final properties of NR vulcanizates. Silica and calcium carbonate (CaCO3 ) are among the fillers of choice when the color of the products is concerned. In this case, a special focus was to compare the vulcanizing efficiency of NR filled with two different filler types, namely nano-sized silica and micrometer-sized CaCO3 . This study focused on the effects of the loading level (10-50 parts per hundred parts of rubber, phr) on the final properties and structural changes of NR composites...

Several composites based on poly(3-hydroxybutyrate) (PHB) and mesoporous SBA-15 silica were prepared by solvent-casting followed by a further stage of compression molding. The thermal stability, phase transitions and crystalline details of these composites were studied, paying special attention to the confinement of the PHB polymeric chains into the mesopores of the silica. For that, differential scanning calorimetry (DSC) and real-time variable-temperature X-ray scattering at small angles (SAXS) were performed...

This study presents an analysis of films which consist of two layers; one layer is PVDF as the matrix, along with fillers BaTiO3 (BT), and the second is one bacterial nanocellulose (BNC) filled with Fe3 O4 . The mass fraction of BT in PVDF was 5%, and the samples were differentiated based on the duration of the mechanical activation of BT. This innovative PVDF laminate polymer with environmentally friendly fillers aligns with the concept of circular usage, resulting in a reduction in plastic content and potential improvement of the piezoelectric properties of the entire composite...

This paper evaluates an experimental wetland as part of a pilot soil reclamation project in a mining area. The wetland was constructed using materials of mining origin from the area; most reactive materials of acid pH were stabilised using limestone filler. The study selected macrophytes that are tolerant to potentially toxic elements (PTEs) and resistant to salinity, namely Phragmites australis , Juncus effusus , and Iris pseudacorus . These macrophytes were then placed in pots containing substrates composed of different mixtures of topsoil, peat, and mining waste (black or yellow sand)...