Stress fractures

Leaf springs are critical components for the railway vehicle safety in which they are installed. Although these components are produced in high-strength alloyed steel and designed to operate under cyclic loading conditions in the high-cyclic fatigue region, their failure is still possible, which can lead to economic and human catastrophes. The aim of this document was to precisely characterise the mechanical crack growth behaviour of the chromium-vanadium alloyed steel representative of leaf springs under cyclic conditions, that is, the crack propagation in mode I...

The low-temperature fatigue crack propagation rate of 925A steel, as a rudder steel for polar special ships, has a crucial impact on the evaluation of the fatigue strength of polar ships. The purpose of this article is to study the fatigue crack propagation rate of 925A steel under different low-temperature conditions from room temperature (RT) to -60 °C. The material was subjected to fatigue crack propagation tests and stress intensity factor tests. The experimental tests were conducted according to the Chinese Standard of GB/T6398-2017...

Developing advanced underwater welding technology for titanium, which is the key structural material for underwater applications, is of great significance for the design, fabrication, and maintenance of submarine equipment. In this study, in order to investigate the underwater welding microstructure and mechanical properties of Ti-4Al-2V alloy, underwater wet laser welding was conducted on Ti-4Al-2V alloy using varying laser power. The microstructure and properties of the welding joints were characterized and analyzed...

PC/ABS composites are commonly used in airbag covers. In this paper, uniaxial tensile experiments of a PC/ABS composite at different temperatures and strain rates were conducted. The results showed that the temperature and loading rate affect the mechanical properties of the PC/ABS composite. As the temperature increases, the yield stress decreases and the strain at the moment of fracture increases, but the strain rate at the same temperature has a relatively small effect on the mechanical properties, which are similar to ductile materials...

Bridge cable wires suffer from alternating stress and environmental erosion, leading to premature failure prior to its design life. This paper investigates the fatigue and mechanical behaviors of corroded bridge cable wires with a zinc-aluminum (Zn-Al) alloy coating. Based on the salt spray corrosion test and microstructure analysis, the anti-corrosion resistance and corrosion appearance characteristics of the Zn-Al alloy coating and galvanized coating were investigated. The Zn-Al alloy coating was superior in resistance to corrosion fatigue for the improvement in toughness and the generation of anti-corrosion Zn-Al and Fe-Zn-Al phases...

The current protocol used to determine if an individual is osteoporotic relies on assessment of the individual's bone mineral density (BMD), which allows clinicians to judge the condition of a patient with respect to their peers. This, in essence, evaluates a person's fracture risk, because BMD is a good surrogate measure for strength and stiffness. In recent studies, the authors were the first to produce fracture toughness (FT) data from osteoporotic (OP) and osteoarthritic (OA) patients, by using a testing technique which basically analyzes the prerequisite stress conditions for the onset of growth of a major crack through cancellous bone tissue...

BACKGROUND CONTEXT: Pelvic ring fractures are becoming more common in the aging population and can prove to be fatal, having mortality rates between 10% and 16%. Stabilization of these fractures is challenging and often require immediate internal fixation. Therefore, it is necessary to have a biomechanical understanding of the different fixation techniques for pelvic ring fractures. METHODS: A previously validated three-dimensional finite element model of the lumbar spine, pelvis, and femur was used for this study...

STATEMENT OF PROBLEM: More data are needed on the influence of preparation design on the fracture strength, failure type, repairability, and polymerization-induced cracks of molar teeth restored with direct composite resin restorations. PURPOSE: This in vitro and finite element analysis study investigated the effect of different preparation designs on fracture strength, failure type, repairability, tooth deformation, and the formation of polymerization-induced cracks of compromised molars restored with direct composite resin restorations...

OBJECTIVES: Multilayer monolithic zirconia (M-Zr) crowns can be engineered to achieve gradational translucency and color intensity. However, this modification may compromise the mechanical strength, raising concerns regarding the ability of M-Zr crowns to withstand occlusal stresses. The effects of M-Zr crown thickness on translucency and ability to endure occlusal forces were investigated at different tooth positions (incisors, premolars, and molars). The objective was to determine the minimal thickness of M-Zr crowns used in tooth preparation to meet aesthetic and functional demands...

Present study investigates the effects of probe size geometry on thermodynamic kinetics, rheology, and microstructure of wheat and tapioca starch. Ultrasound treatment using different probe diameters (20 mm and 100 mm) significantly influenced the gelatinization process. Results showed reduced enthalpy (ΔH) and Gibbs energy (ΔG), indicating enhanced gelatinization efficiency. According to the results, using a 20 mm and 100 mm probe leads to a reduction of 52.7 % and 68.6 % in reaction enthalpy for wheat starch compared to native starch, respectively...

The problem of wellbore leakage is a key challenge in the petroleum industry, limiting drilling progress and increasing drilling costs. Plugging agents play a role in repairing leaks and fractures; however, traditional plugging materials generally have low mechanical strength, poor adaptability to permeable strata, limited water absorption and expansion capabilities, and poor temperature and salt resistance. To address these limitations, a pioneering polyacrylic acid-polyacrylamide (PAA/PAM) double-network hydrogel was synthesized through aqueous solution polymerization in this study...

This study investigates the viscoelastic deformation mechanisms of bone as a response to Vickers hardness indentation. We utilized advanced high-resolution scanning electron microscopy (SEM) to investigate a distinct deformation pattern that originates from the indentation site within the bone matrix. The focus of our research was to analyze a unique deformation mechanism observed in bone tissue, which has been colloquially termed as "screw-like" due to its resemblance to a screw thread when viewed under an optical microscope...

PURPOSE: The aim of this work is to conduct a literature review to highlight all the parameters involved in sub-prosthetic radicular fractures of teeth supported by metallic dental core. MATERIALS AND METHODS: The following research was performed among published studies over the last 10 years in two PubMed/Medline and Scopus and supplemented by manual searching within the bibliographies. The search was restricted to publications in English and French. RESULTS: Out of the 1464 articles initially identified, 18 studies met our inclusion criteria and were subsequently included in the literature review...

Ankle instability, which can be attributed to either the deltoid or lateral ligamentous complex, may be both a cause and a consequence of ankle fractures. This study aimed to assess postoperative ankle instability in patients with displaced ankle fractures. A total of 54 patients with displaced ankle fractures were included. Malleolar fractures were surgically reduced and fixated, and if necessary, the syndesmosis was stabilized. Concomitant deltoid injuries were left unrepaired. Ankle stress radiographs were taken approximately 25...

BACKGROUND: The Proximal Femoral Nail Antirotation (PFNA) device is the most commonly used implant to fix unstable femoral trochanteric fractures (UFTFs), but it has a relatively high incidence of complications. Due to this factor, the modified intramedullary nail (MIN) was created to treat patients with UFTFs. The aim was to exhibit the MIN and make a comparison with PFNA and InterTAN using biomechanical methods. METHODS: An adult UFTF model was developed using Mimics software...

This study investigates the optimal placement of locking plate screws for bone fracture stabilization in the humerus, a crucial factor for enhancing healing outcomes and patient comfort. Utilizing Finite Element Method (FEM) modeling, the research aimed to determine the most effective screw configuration for achieving optimal stress distribution in the humerus bone. A computer tomography (CT) scan of the humerus was performed, and the resulting images were used to create a detailed model in SOLIDWORKS 2012...

UNLABELLED: A snow slab avalanche releases after failure initiation and crack propagation in a highly porous weak snow layer buried below a cohesive slab. While our knowledge of crack propagation during avalanche formation has greatly improved over the last decades, it still remains unclear how snow mechanical properties affect the dynamics of crack propagation. This is partly due to a lack of non-invasive measurement methods to investigate the micro-mechanical aspects of the process...

BACKGROUND: Up to 25% of the tooth extraction after root canal treatment could be attributed to the vertical root fracture (VRF). The treatment choice for teeth with VRF would mostly be the extraction despite some repairing methods were also reported. The repairing treatment result of VRF would mostly depend on the fixation strength and the bioactivity of the repairing materials, especially for the posterior teeth with high masticating stresses. This case report designed a novel surgical treatment approach for the VRF of posterior teeth...

The global burden of osteoporosis continues to rise with an ageing population. Untreated osteoporotic fractures not only heighten the risk of subsequent fractures but are associated with excess mortality. Although primary care guidelines consistently stress the importance of secondary fracture prevention, fewer than 20% of patients are appropriately treated for osteoporosis following an initial osteoporotic fracture. This worldwide phenomenon is known as the osteoporosis care gap. This literature review examines the barriers to secondary fracture prevention in primary care and evaluates the effectiveness of targeted primary care interventions...

Introduction Limited research exists on the association between coronavirus 2019 (COVID-19) infection and outcomes following surgical fixation for humerus fractures. The objective of this study was to evaluate the effects of COVID-19 on the clinical outcomes of patients undergoing humerus fracture surgery. Methods Approval to utilize insurance claim data from the Change Healthcare dataset was obtained from the Datavant COVID-19 Research Database. Patients older than 55 years old who underwent humerus fracture surgery from April 1, 2020, to March 1, 2022, were included in the analysis...