Journal of Prosthodontics : Official Journal of the American College of Prosthodontists

PURPOSE: The purpose of this study was to evaluate the flexural strength (FS), flexural modulus (FM), and fatigue limit (FL) of 3D-printed resin-based polymers and composites and compare them to 3D-printed composites. MATERIALS AND METHODS: A bar-shaped specimen (25 × 2 × 2 mm) was CAD designed according to ISO 4049:2019, and 60 duplicates of the 3D model were nested at a 45-degree angle with the printing platform and 3D-printed with three materials: denture teeth resin (Denture Teeth, Formlabs), temporary crown and bridge resin (Temporary CB, Formlabs), and composite (Flexcera Smile Ultra+, Desktop Health)...

PURPOSE: The purpose of this study was to evaluate and determine clinical outcomes and survival rates of straight and extended length subcrestal angulated (ELSA) implants (20-24 mm lengths) placed for immediate (up to 72 h post-operative) or delayed rehabilitation (4 months post-operative) of severely atrophic maxillae. Prosthetic treatment consisted of interim and definitive implant-supported fixed implant-supported prostheses with up to 3 years of function. MATERIALS AND METHODS: A retrospective analysis was conducted of 38 patients (five dropped out; final total was 33), treated between 2017 and 2019 in a private practice...

PURPOSE: Reference values of occlusal characteristics are needed to interpret the data obtained using the T-Scan System. This study aimed to establish reference values for and to assess the reliability of, occlusal force distribution in the maximal intercuspal position and the occlusion time in young adults with healthy dentition. MATERIALS AND METHODS: In total 178 adults with natural dentition participated in this retrospective cross-sectional study, of whom 76 performed a retest session...

PURPOSE: The objective was to determine the accuracy of 3D-printed dental models subjected to different storage conditions using six different material and printer combinations. MATERIALS AND METHODS: Three completely dentate models were designed using dental CAD software (3Shape Dental System). A horseshoe-shaped solid base with a posterior horizontal bar was used. The models were printed in a horizontal direction against the building platform without support. The models were printed using six printers with the corresponding recommended resin material: Carbon M2 (DPR10), HeyGears A2D4K (Model HP UV2...

The aim of this report was to digitize traditional denture relining using a digital duplication method, in addition to assessing the wear resistance of three-dimensional (3D) printed denture teeth. A complete denture was relined using light body impression. The denture with impression was scanned yielding a standard tessellation language file that was designed to print the denture base and teeth. The printed teeth were fitted into the sockets of the printed denture base and then bonded using auto-polymerized acrylic resins, followed by finishing and polishing...

PURPOSE: The aim of this study was to analyze the impact of various surface treatments and production methods on the shear bond strength (SBS) between reline material and denture base resins. MATERIALS AND METHODS: One-hundred-twenty specimens were produced using conventional heat-polymerization, subtractive, and additive techniques. Each group consisted of 40 specimens. The specimens were divided into four subgroups, each with 10 samples, for surface treatments...

PURPOSE: The aim of this study was to investigate and compare the influence of zirconium dioxide nanoparticles (ZrO2 NPs) and silicon dioxide nanoparticles (SiO2 NPs) addition and printing orientation on the flexural strength (FS) of provisional three-dimensional (3D) printing resins undergoing thermal cycling (TC). METHODS: Three dimensional-printed resin (NextDent C&B MFH) was used to fabricate 300 bar-shaped specimens (25 × 2 × 2 mm3 )...

PURPOSE: To evaluate the effects of exposure protocol, voxel sizes, and artifact removal algorithms on the trueness of segmentation in various mandible regions using an artificial intelligence (AI)-based system. MATERIALS AND METHODS: Eleven dry human mandibles were scanned using a cone beam computed tomography (CBCT) scanner under differing exposure protocols (standard and ultra-low), voxel sizes (0.15 mm, 0.3 mm, and 0.45 mm), and with or without artifact removal algorithm...

PURPOSE: This study aimed to develop and evaluate a simple, non-destructive method for assessing the misfit and passivity of implant-retained prostheses frameworks. MATERIALS AND METHODS: To simulate the rehabilitation of a mandible posterior partially edentulous area using 3-unit screw-retained frameworks supported by two implants were fabricated and divided into the following five groups (n = 10 in each group): OP = one-piece framework cast in Co-Cr with the conventional method (control-group); Co-Cr frameworks sectioned and welded by laser (=LAS) or tungsten inert gas (=TIG); Co-Cr CAD-CAM = milled Co-Cr framework; Zir CAD-CAM = milled zirconia framework...

Replacement of missing or hopeless teeth in the esthetic zone is one of dentistry's most critical challenges. In the past, multiple surgical procedures have been needed to reconstruct compromised extraction sites. The surgeries have been associated with long healing times and increased morbidity, all the while patients are using either fixed or removable interim restorations. The procedures identified in this paper minimize surgical operating times, healing times, and delays in obtaining definitive restorations by combining multiple surgical procedures in one visit...

Passive fit is essential for multiple-unit implant-supported prostheses. Conventional methods to assess the passivity of complete-arch implant-supported prostheses do not allow 3-dimensional (3D) visualization and quantification of misfit. This report describes the marginal and internal fit evaluation of a complete-arch implant-supported prosthesis by using the triple-scan protocol involving a scanner and a 3D analysis freeware. This technique allows researchers, clinicians, or dental technicians to detect and quantify 3D prosthetic misfit, which may facilitate the preparation for dental appointments and objective measurement of misfit for research studies...

PURPOSE: Attempts have been made to decontaminate the implant surface by using diode lasers. However, the parameters that provide efficient decontamination without altering the topography or surface characteristics of titanium implants are still unclear. The aim of the present study was to evaluate the effect of altering the power of diode laser (940 nm) application on the hydrophilicity, surface topography, and chemical composition of sandblasted, large grit, acid-etched (SLA) treated titanium alloy implant surface...

PURPOSE: Speed sintering was introduced to fabricate time-efficient chairside restorations, however, its influence on the microstructure and optical properties of zirconia is still unclear. This study investigated the influence of speed sintering on the microstructure and optical properties of ultra-translucent multi-layered cubic zirconia. MATERIALS AND METHODS: Ultra-translucent cubic zirconia (Katana™ UTML; Kuraray Noritake Dental Inc., Aichi, Japan) was cut into a total of 80 specimens, twenty within each layer of the blank...

PURPOSE: This systematic review aimed to verify whether anatomic, semi-anatomic, or nonanatomic occlusal morphology of artificial teeth improves the masticatory function of complete or removable partial denture wearers. MATERIALS AND METHODS: According to the PICO strategy, six databases and the grey literature were searched to identify randomized (RCT) and non-randomized clinical trials (N-RCT) comparing masticatory function, in terms of masticatory performance and efficiency, and muscle activity as primary outcomes; and patient-reported results (O) in individuals using removable dentures (P) with different occlusal morphologies of artificial teeth (I/C)...

The purpose of this article is to describe a technique to accurately cement implant crowns on an abutment extraorally and prevent misalignment that might change the desired position of the crown on the abutment when delivered. An implant-retained crown was tried-in and occlusal and interproximal contacts were adjusted for delivery. The cementation verification aid was fabricated using a polyvinylsiloxane bite registration material (Blu Mousse) to cement the crown onto the abutment extraorally to ensure proper alignment of the crown on the abutment...

PURPOSE: To measure the wear at the implant interface between the Grade 4 titanium (Ti) of the implant and frameworks fabricated using two additively manufactured alloys (Ti alloy and cobalt-chromium [Co-Cr]) pre- and post-artificial aging. MATERIAL AND METHODS: Three-unit frameworks supported by two implants were additively manufactured (Atlantis; Dentsply Sirona) using Ti and Co-Cr dental alloys. Two implants (OsseoSpeed EV, Astra Tech; Dentsply Sirona) were torqued on each non-engaging framework...

Chondrosarcoma is among the most common primary bone tumors in adults. In the mandible, chondrosarcoma is a very uncommon malignant cartilage-producing tumor. This case report shows how virtual planning combined with other digital technologies may improve masticatory function rehabilitation in patients with enlarged mandibular chondrosarcoma. The present study reports a case of a 52-year-old male patient who was initially diagnosed with a mandible chondroma, which was successfully excised with no evidence of malignant transformation...

PURPOSE: The purpose of this in vitro study was to compare the tensile bond strength (TBS) of resin nanoceramics (RNC), zirconia, and lithium disilicate (LS2) restorations cemented to titanium abutments before and after thermomechanical aging. MATERIALS AND METHODS: Twelve specimens per group were fabricated to determine the TBS between a titanium abutment and 4 types of crown materials (2 RNCs, LS2, and translucent zirconia crowns for the maxillary molar). After milling, the abutments and crowns were cemented with resin cement after air-particle abrasion...

PURPOSE: To investigate the effects of shade tab color variations (tooth-colored versus gingiva-colored) and surface treatment (application of mineral oil) on the trueness of color reproduction from dental shade tabs to 3D-printed full-color dental casts, using digital scans obtained from an intraoral scanner. MATERIALS AND METHODS: Pristine tooth-colored (with 16 shade tabs) and gingiva-colored (with 5 shade tabs) shade guides were digitally scanned using an intraoral scanner, and subsequently, 3D-printed replicas were created using a full-color material jetting 3D-printer...

PURPOSE: To evaluate the color, surface properties, and flexural strength of 3D-printed permanent crown resin subjected to different post-polymerization conditions after artificial aging. MATERIALS AND METHODS: Ninty (10×2 mm) disc-shaped specimens were printed by using permanent crown resin with SLA technology. Specimens were divided into nine different groups, subject to post-polymerization conditions at three different times (15, 20, and 30 min) and three different temperatures (40,60 and 80°C)...